Dagom'App

Application for Dagoma 3D printers


Clarico-Image-Text

 Requirements


Before going any further, download and install Cura by Dagoma. During the installation, we add the necessary elements for the proper functioning of Dagom'app.

  FOR UNDERSTANDING 

What is the Dagom'App for?

1 - Updating the internal software of the 3D printer (or firmware)

2 - Setting the first layer (or offset) for 3D Disco printers

3 - Direct access to our online support

Clarico-Picture
Dagom'app home screen

1 - Updating the internal software of the 3D printer (or firmware)

Clarico-Image-Text

STEP 1


Select "I set up my printer".

Clarico-Image-Text

STEP 2 


 Check the steps once they have been checked.

The USB-B cable is supplied with the 3D printer. It is also available hereDiscoVery printers only will require a mini USB-B cable.


Clarico-Image-Text

STEP 3


Select your 3D printer model.


Clarico-Image-Text

STEP 4


Connect your computer to the electronic board of your 3D printer using the USB cable.

You must have installed the Cura by Dagoma software beforehand for the printer to be recognized (installation of the 3D printer drivers with Cura by Dagoma).

 
 

Clarico-Image-Text

STEP 5


Select "I give new powers" then click on the blue arrow to validate.


Clarico-Image-Text

STEP 6


Click on "Select a .hex file" to choose the new firmware version to be installed. 

The .HEX file is to be downloaded on our platform. dist.dagoma.fr.


Clarico-Image-Text

STEP 7


Once you have selected the .hex file, click "Flasher" to update the 3D printer. 

This action may last a few minutes.

Do not unplug your 3D printer.


Clarico-Image-Text

UPDATE DONE 


Your 3D printer has been updated. You can close Dagom'App and remove the USB cable.

The update has removed the settings from your first layer (offset). You need to recalibrate your 3D printer (see below).


2 - Adjust the first layer (calibration phase) 

CALIBRATION MAGIS ET NEVA


Unplug the 3D printer. Press and hold the main button of the Magis/Neva. While holding down the button, reconnect the 3D printer to the power supply and continue to hold down the button until the first movement of the print head.

Calibration is fully automatic. It can take up to 5 minutes. Caution, the print head must be clean (no filament residues).


  Dirty print head                     Clean print head   



Clarico-Image-Text

CALIBRATION  DISCO

Before starting the calibration, you have a small adjustment to make.

Make sure that the bars on which the head moves are parallel to the platter.

Place the 3D printer in front of you. You are going to act manually on the couplers as in the video to move the axis up or down.

For precise adjustment, place the platen in the center of the machine with the head to the left.

Lower the head so that the nozzle touches the tray. Move the head manually to the right and touch the plate again.

When the head touches the platter from left to right, your setting is good. You can proceed to calibration.


 
 

Clarico-Image-Text

STEP 1


Select "A perfect impression" in Dagom'App.

Find out how to connect your 3D printer to your computer in the previous steps on this page.


Clarico-Image-Text

STEP 2


Select "First Layer Setting".


Clarico-Image-Text

STEP 3


Insert filament into your 3D printer.

Discovery/Easy sans Extrudeur+ Disco Ultimate ou avec Extrudeur+

 
 

 
 

The adjustment target is supplied with your 3D printer. 

Clarico-Image-Text

STEP 5


Place the target on the tray and under the nozzle, then click the arrow to go to the next step.


Clarico-Image-Text

STEP 5


You will now adjust the height of the print head.

Lower the head little by little using the down arrow in Dagom'App.

Move the target back and forth. When you feel resistance, stop moving the target back and forth. Once the map is slightly stuck, proceed to the next step. 

 
 
 


Clarico-Image-Text

STEP 6


Your 3D printer is now ready to print test pellets.

It will move a little, warm up and then start printing.

In the next step, you will precisely adjust the height of the first layer.


Clarico-Image-Text

STEP 7


In this interface, you will be able to go up or down the height of the first layer.

If it is over-crushed, it may damage your mounting bracket. Click on "higher".

If it's too high, the filament won't fit on the set. Click on "lower".

Once the layer height is good, click on "I am satisfied" and then click on "Save".

 
 

Clarico-Image-Text

CALIBRATION DONE


Congratulations, your 3D printer is set.

You can close Dagom'App and remove the USB cable.